Cheetah Mounts APSAMB 32-55″ LCD TV Wall Mount Bracket with Full Motion Swing Out Tilt & Swivel Articulating Arm for Flat Screen Flat Panel LCD LED Plasma TV and Monitor Displays Includes Free 10′ Braided High Speed HDMI Cable With Ethernet
Cheetah Mounts APSAMB 32-55″ LCD TV Wall Mount Bracket with Full Motion Swing Out Tilt & Swivel Articulating Arm for Flat Screen Flat Panel LCD LED Plasma TV and Monitor Displays Includes Free 10′ Braided High Speed HDMI Cable With Ethernet
- Collapses to less than 4″ from the wall
- Extends to a full 26″ from the wall
- High quality powder coat finish
- Built-in bubble level in wall plate
- Dual safety screws to lock TV Position
The APSAM universal articulating arm mount supports virtually any display up to 55-Inch with hole patterns up to 27.7-Inch horizontally and 19-Inch vertically. The APSAM also features a full 27-Inch of extension and up to 150 degrees of rotation for larger displays, it also folds to a low 3.5-Inch profile as has +/-15 degrees of tilt. The APSAM mount is designed with a lift and lock design for ease of installation and is constructed with a 17-Inch wall plate which is specifically designed for in
List Price: $ 159.96
Price: [wpramaprice asin="B000WL0I1I"]
[wpramareviews asin="B000WL0I1I"]
[wprebay kw="lcd+tv+wall+mount+bracket" num="6" ebcat="-1"] [wprebay kw="lcd+tv+wall+mount+bracket" num="7" ebcat="-1"]
Find More LCD TV Wall Mount Bracket Products
(11442)
(12435)
Does the job, but I’m disappointed with the end result,
I just installed this wall mount for use with a 42″ Philips plasma screen TV. As you can see from the picture, the mount basically consists of two plates connected by an articulating arm, which provides the swivel action. The TV is secured to the larger of the two plates via the supplied brackets, which provide the tilt action. The mount itself comes pre-assembled and thus requires only installation onto the wall; similarly, the brackets are also pre-assembled (with the exception of a pair of adjustment knobs for the tilt mechanism which for some reason are not mentioned at all in the installation instructions), and need only be screwed into the back of the TV.
Despite some headaches presented by the construction of my wall (I rent an apartment in an old building in Brooklyn where there is apparently an inch-and-a-half of plaster overlying drywall and studs), I was able to install the smaller plate into the wall using some cheap-but-sturdy toggler anchors from the local hardware store, without a problem.
Where I did run into a problem was when I mounted the TV to the larger of the two plates. Basically, though the mount seems solidly constructed and holds up just fine, it seems as though the articulating arm isn’t strong enough at the joint, which causes a distinct and noticeable (about 3-5 degrees or so) right-sided droop to the TV; this despite the fact that the smaller plate affixed to the wall is perfectly level. Now, given that the mount is rated for TVs up to 55″, I don’t think my 42″ TV is outside of its reported weight range. So, given that the wall plate is level, and eliminating the weight of the TV as the source of the problem, I can only chalk it up to a design or manufacturing defect.
Now, the droop makes the whole thing look kind of sloppy, though in truth it doesn’t really affect the viewing experience all that much; it’s slight enough so that you don’t notice it at all once you’re engrossed in whatever it is you’re watching. And this is definitely the cheapest tilt-and-swivel mount I’ve been able to find, which offsets a little bit of my disappointment. In sum, I’d say I’m satisfied enough that I won’t bother to go through the hassle of trying to return it, but if I were to do it all over again I might have saved up for a slightly more expensive model from a different manufacturer.
Was this review helpful to you?
|Really good except for one issue,
I just finished installing this mount and my 50″ Panasonic plasma. I bought the articulating mount so I could position the TV in the corner. This means I mounted it towards the corner of one wall and used the articulation to move it to a diagonal position where the edges are flush against adjacent walls.
This mount was very easy to install. Instructions were great. I really liked the built-in level. It was easy to get the plasma on the mount with two people.
The one issue I had was with the tv actually being level. The tv is level when it’s flat against the wall. When I articulate it out a bit and to the right, the right edge dips. It’s obvious enough to bother me. What I did was adjust one of the brackets that bolt to the tv. I purposely had one bracket one position different (higher) than the other. This resulted in leveling the tv when articulated. However, when I put the tv back against one wall, it’s grossly off level. That’s ok for me because the permanent spot is in the corner which is level. I think the problem is due to the weight pressing down on the arm. Not much you can do about it.
Was this review helpful to you?
|Not easy to install, but worth the money if you know what you’re doing,
Although I’m not a “Professional” installer, this installation makes the 8th Plasma/LCD wall mount installation I’ve done over the years. I’ve often spent over $250+ on previous wall kits and thought after reading the previous customer feedbacks; I would save some money and try something new.
In the past I’ve almost always bought OmniMount wall mounts, primarily due their ease of installation. This product was NOT easy to install, and had I not had prior experience hanging TV’s, this COULD HAVE proven to be a disaster.
For starters, there is no “Template” to assist with hole drilling, not even a listed measurement to show how much space to drill the upper and lower holes. This is something that is standard with OmniMount and something I missed having. Holding the mount on the wall to Pencil or mark the holes can be a chore unless you know EXACTLY where the studs are and you have more than one set of hands. If you have some carpenter skills, you’ll be able to measure and mark your spots easier than someone who doesn’t.
Second, don’t buy this mount if you DON’T have a “specific” place where you want to mount your TV. The main bracket is just over 16″ wide and HEAVY. I wouldn’t count on this holding a TV unless you’re drilled into two studs and using all 4 Lag Bolts. Seeing that most studs are 16″ on center, there is no wiggle room to install the bracket left or right. Other mounts I’ve worked with are about 20″ wide to allow for a greater range of installation.
Third, the mounting bolts that came with the kit are only 1.5″ long. In my opinion, to properly hold the mount AND TV, I wouldn’t go with anything less than 3″ bolts, anything less could be a risk.
Forth, the bolts used to mount the brackets to the back of the TV were way to short, especially if you have to use the included spacers. Finding longer bolts was NOT an easy chore as both the size and type of thread are not common. I was fortunate to have extra bolts left over from prior installations, however I still wish I had longer bolts. Neither Home Depot nor Lowes had the right thread type.
Fifth, the brackets that mount to the back of the TV have “pre-drilled” holes on the top, and “oval” type holes in the bottom. The PRO: It’s very easy to make sure that the right and left brackets will be installed evenly and there is no need to run a level to make sure the TV will hang correctly. The CON: Because of the design and where cross brackets are installed on the mount, you may have to settle for your TV hanging higher or lower than you originally wanted. I would HIGHLY suggest installing the TV brackets FIRST, so you can find a true center for mounting BEFORE you mark and drill anything on the wall. This is completely opposite of the installation directions that come with the mount. Installers beware for sure…..
Overall this is a very solid product and for the most part I’m happy with the quality. The TV is hung, and with my past install experience, this install went fairly smoothly. I’m quite confident that had this been my first install, I would’ve had many errors and A LOT of holes to patch. If you’re good with a tape measure, know how to find the studs in your wall and have an extra set of hands, this mount will be a good value for the money.
If you’ve never attempted this type of install before and you think a stud finder is a cougar in a bar, get a professional to help you with this or spend more on a name brand mount.
Suggestions on having a smoother install (some were already listed above)
- Install the left and right TV brackets FIRST. 1) To make sure the brackets will fit your TV. 2) To make sure the bolts are long enough (won’t be if you have to use the spacers). 3) To find the true center so you know just how high or low you need to hang the TV. Had I not followed this step, I would have ended up 3″ off center and I would’ve had to patch four rather large holes in the wall.
- When installing the mounts to the back of the TV, make sure you have AT LEAST a half inch screws into the back of the TV. Make sure your thread size matches the bolt that DOES work with your TV to avoid stripping the thread on the inside of the TV.
- Purchase longer Lag Bolts to mount the main mount to the wall (wait till your mount arrives to match the right diameter).
- Remove the bracket that the TV hangs on from the wall mount (four screws covered by black plastic caps) prior to marking and mounting the wall mount. This will reduce some of the weight and will make your install go a little smoother. CAUTION: There are clear NYLON washers that sandwich the plate so be careful when removing the bolts so as not to lose them. Remember the order of the washers as it’s designed to allow the TV to swivel along its horizon. When reinstalling these nuts and bolts, it should be tight but not OVER tight. The TV may be…
Read more
Was this review helpful to you?
|